Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
They are making several great annotation on the subject of A Step-by-Step Guide to Installing a Bathtub as a whole in this article directly below.
Mounting a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough task. If the old bathtub is readily obtainable, the task can move rapidly; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. Make sure you have qualified on your own for the job as well as are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed task, it is far better to take into consideration using one before you start. Possibilities are you might need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your shower room if you have actually currently purchased a new bathtub and do not require to transform the plan of your previous water pipelines.
Your devices as well as material list should consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be quite bothersome due to the limited gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers are in area between the faucet and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The former kind should be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using the two wooden boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next goal is to ensure that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the level reviews level.
To set up faucets, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill the bath tub as well as additionally check the overflow outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub ought to wait up until the bath tub has been used at the very least once as this will resolve it into its final setting.
Preparing for the Installment
To start with, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its final placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, triggering the water to penetrate the wall between the bathroom and also the tiling, causing problems with wetness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split fairly early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very interested by A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed reading the entire page. If you enjoyed our page if you please remember to share it. Thanks a bunch for your time. Please stop by our website back soon.
Visit Site Report this page